kumar ideology

How to find The value of Burnt Resistor ( By three handy Methods ) Find The value of Burnt Resistor by Three Simple Methods  We can find the Values of  burnt resistors  by these three handy methods below. Method 1 Scarp the outer coating. Clean the Burnt Section of the resistor. Measure resistance from one end of the resistor to the damaged section. Again measure the resistance from damaged section to the other end of the resistor. Add these two value f resistances. This is the approximate value of Burnt resistor.  Just add a small value of resistance for damaged section i.e., suppose the value of burnt resistor was 1k Ω, but you got 970 Ω. So just add 30 Ω, and you will have 1k Ω. Also Read:  How to check a Capacitor by 4 Simple Methods Method 2 This method can also be used for finding the value of  burnt resistor(s) (also, may be applied on connected resistors in the circuit) in case if you don’t know about Resis...

What is slip in an induction motor? Slip can be defined as the difference between the flux speed (Ns) and the rotor speed (N). Speed of the rotor of an induction motor is always less than its synchronous speed. It is usually expressed as a percentage of synchronous speed (Ns) and represented by the symbol ‘S’.

Why back emf used for a dc motor? highlight its significance. The induced emf developed when the rotating conductors of the armature between the poles of magnet, in a DC motor, cut the magnetic flux, opposes the current flowing through the conductor, when the armature rotates, is called back emf. Its value depends upon the speed of rotation of the armature conductors. In starting, the value of back emf is zero.

What are the various kind of cables used for transmission? Cables, which are used for transmitting power, can be categorized in three forms: • Low-tension cables, which can transmit voltage upto 1000 volts. • High-tension cables can transmit voltage upto 23000 volts. • Super tension cables can transmit voltage 66 kV to 132 kV.

How can you relate power engineering with electrical engineering? Power engineering is a sub division of electrical engineering. It deals with generation, transmission and distribution of energy in electrical form. Design of all power equipments also comes under power engineering. Power engineers may work on the design and maintenance of the power grid i.e. called on grid systems and they might work on off grid systems that are not connected to the system.

Why AC systems are preferred over DC systems? Due to following reasons, AC systems are preferred over DC systems: a. It is easy to maintain and change the voltage of AC electricity for transmission and distribution. b. Plant cost for AC transmission (circuit breakers, transformers etc) is much lower than the equivalent DC transmission c. From power stations, AC is produced so it is better to use AC then DC instead of converting it. d. When a large fault occurs in a network, it is easier to interrupt in an AC system, as the sine wave current will naturally tend to zero at some point making the current easier to interrupt. Due to following reasons, AC systems are preferred over DC systems: a. It is easy to maintain and change the voltage of AC electricity for transmission and distribution. b. Plant cost for AC transmission (circuit breakers, transformers etc) is much lower than the equivalent DC transmission c. From power stations, AC is produced so it is be...

State the difference between generator and alternator Generator and alternator are two devices, which converts mechanical energy into electrical energy. Both have the same principle of electromagnetic induction, the only difference is that their construction. Generator persists stationary magnetic field and rotating conductor which rolls on the armature with slip rings and brushes riding against each other, hence it converts the induced emf into dc current for external load whereas an alternator has a stationary armature and rotating magnetic field for high voltages but for low voltage output rotating armature and stationary magnetic field is used.

Why star delta starter is preferred with induction motor? Star delta starter is preferred with induction motor due to following reasons: • Starting current is reduced 3-4 times of the direct current due to which voltage drops and hence it causes less losses. • Star delta starter circuit comes in circuit first during starting of motor, which reduces voltage 3 times, that is why current also reduces up to 3 times and hence less motor burning is caused. • In addition, starting torque is increased and it prevents the damage of motor winding.

a book of protection and switch gear by badriram CLICK HERE  TO DOWNLOAD THE BOOK . . . . . . ↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓ . . . . . https://drive.google.com/open?id=0B-xPXNqqPzIITnhpUzk1M25teUk . . . . . . . . If you want more book, slide, ppts and notes online you can request in the comment section , Visit this site for more books, slide, ppts, notes and share this site link with the needy one. Thank You

                                        MOVING IRON  • Moving-iron instruments are generally used to measure alternating voltages and currents.  • In moving-iron instruments the movable system consists of one or more pieces of soft iron, which are so pivoted as to be acted upon by the magnetic field produced by the current in coil. Components  • Moving element: a small piece of soft iron in the form of a vane or rod.  • Coil: to produce the magnetic field due to current flowing through it and also to magnetize the iron pieces.  • In repulsion type, a fixed vane or rod is also used and magnetized with the same polarity.  • Control torque is provided by spring or weight (gravity).  • Damping torque: the damping device consisting of an air chamber and a moving vane attached to the instrument spindle.  • Deflecting...